HOLYBRO

-Digital airspeed sensor kit for fixed-wing UAVs and VTOL platforms.
-Uses MS4525DO pressure sensing with PT40 pitot tube hardware.
-Supported by Holybro flight controllers with PX4 and ArduPilot.

-DroneCAN GPS module with u-blox M9N receiver and BMM150 compass.
-Uses CAN communication for improved reliability in UAV wiring.
-Does not occupy a flight controller serial port and supports CAN hub integration.

-Professional DroneCAN compass module based on the RM3100 magnetometer.
-IP66-rated enclosure for improved protection in demanding UAV environments.
-42cm cable version for flexible installation away from electromagnetic noise.

-DroneCAN optical flow and distance sensor for GPS-denied positioning.
-Combines PixArt optical flow, Broadcom ToF ranging and a 6-axis IMU.
-Designed for Pixhawk-compatible controllers through a 4-pin CAN connection.

-High-precision RTK base station module for UAV positioning systems.
-Uses u-blox ZED-F9P technology with high-gain antenna configuration.
-Designed to provide accurate correction data for rover modules.

-High-precision RTK rover module based on the u-blox ZED-F9P receiver.
-Designed for centimeter-level positioning on UAV platforms.
-Includes IST8310 compass and multi-band GNSS support.

-Ultra-lightweight RTK GNSS rover module designed for UAVs, VTOL aircraft, and weight-sensitive autonomous platforms.
-Built around the u-blox ZED-F9P receiver with an integrated helical antenna and IST8310 compass
-It provides centimeter-level RTK positioning, multi-band GNSS reception, fast acquisition, and reliable navigation performance while weighing less than 25 g.

-Compact flight controller designed for fixed-wing aircraft, VTOL platforms, and small UAVs.
-Powered by an STM32F405 processor with an ICM-42688-P low-noise IMU, integrated SPL06 barometer, analog OSD, onboard current and voltage sensing, dual BEC outputs, 5 UARTs, and 7 PWM outputs.
-Supports ArduPilot, INAV, and Betaflight firmware.

-High-performance flight controller designed for FPV drones, multirotors, and autonomous UAV platforms.
-Powered by a 480 MHz STM32H743 processor with an ICM-42688-P IMU, SPA06 barometer, integrated Bluetooth, analog OSD, MicroSD Blackbox logging, 6 UARTs.
-Support for up to 8 motor outputs. Compatible with Betaflight, INAV, ArduPilot, and PX4.

-Multi-constellation GNSS module designed for Pixhawk-compatible UAV and autonomous systems.
-Powered by the u-blox M10 receiver with an integrated IST8310 compass, high-gain ceramic patch antenna, RGB status LED, buzzer, and safety switch.
-The standard JST-GH 10-pin connection provides direct integration with compatible GPS1 ports.

-High-performance multi-constellation GNSS module designed for Pixhawk-compatible UAV and autonomous systems.
-Powered by the u-blox M9N receiver with an integrated compass, high-gain ceramic patch antenna, RGB status LED, buzzer, and safety switch.
-The standard JST-GH 10-pin connection enables direct integration with compatible GPS Module and GPS1 ports.

-Compact multi-constellation GNSS module designed for UAVs, FPV drones, fixed-wing aircraft, and autonomous platforms.
-Powered by the u-blox M10 receiver with an integrated IST8310 or IST8308 compass.
-It supports simultaneous GPS, Galileo, GLONASS, and BeiDou reception, high-speed navigation updates, and reliable positioning in a lightweight 14–16 g design.

-Compact analog On-Screen Display module designed for FPV drones, UAVs, and Pixhawk-compatible flight systems.
-Built around an ATmega328P microcontroller and MAX7456 monochrome OSD chip.
-It displays essential flight and telemetry information directly on the analog video feed while maintaining an ultra-lightweight 3g design.

-High-performance autopilot flight controller designed for professional UAVs, autonomous vehicles, multirotors, fixed-wing aircraft, and VTOL platforms.
-Powered by an STM32H743 processor with redundant ICM-42688-P and BMI088 IMUs, integrated vibration isolation, multiple CAN and GPS interfaces, and 16 PWM outputs.
-The durable aluminum housing provides a robust solution for demanding research, development, and commercial UAV applications.

-Compact high-performance autopilot flight controller designed for professional UAVs, multirotors, fixed-wing aircraft, VTOL platforms, and autonomous vehicles.
-Powered by an STM32H743 processor with redundant ICM-42688-P and BMI088 IMUs, integrated vibration isolation, 14 PWM outputs, dual CAN buses, and multiple GPS and telemetry interfaces.
-The current Model-A version features improved PWM signal stability under load.

-Professional high-performance autopilot flight controller set designed for commercial UAVs, multirotors, fixed-wing aircraft, VTOL platforms, and autonomous vehicles.
-Powered by an STM32H753 processor with triple ICM-45686 IMU redundancy, BalancedGyro™ technology, dual barometers, advanced vibration isolation, Ethernet, dual CAN buses, 16 PWM outputs, and digital power monitoring.
-Supplied as a complete set with flight controller module, baseboard, PM02D power module, and cable set.

-Complete high-performance autopilot and AI companion computer bundle designed for advanced UAVs, autonomous aircraft, robotics, computer vision, and edge AI applications.
-Combines a Pixhawk 6X flight controller with triple ICM-45686 IMUs and an NVIDIA Jetson Orin NX 16GB companion computer delivering up to 100 TOPS of AI performance.
-Supplied with the Pixhawk Jetson Baseboard, aluminum case, 512GB NVMe SSD, Wi-Fi and Bluetooth connectivity, IMX219 camera, cooling system, PM02D power module, UBEC, PDB, and cable set.

-Compact analog power module designed for Pixhawk-compatible UAV and autonomous systems.
-Supports 2–12S LiPo batteries and provides regulated 5.2V / 3A power to the flight controller while measuring battery voltage and current through an analog interface.
-Features pre-installed XT60 connectors, integrated current sensing, and a lightweight 20g design.

-Digital power module designed specifically for Holybro Pixhawk 5X and Pixhawk 6X flight controllers.
-Supports 2–12S LiPo batteries and provides regulated 5.2V / 3A power while transmitting accurate battery voltage and current data through an I2C digital interface.
-Features integrated current sensing, pre-installed XT60 connectors, and a lightweight 20g design.

-Digital power module and integrated power distribution board designed for Pixhawk 5X, Pixhawk 6X, and compatible FMUv6X flight controllers.
-Supports 2–6S LiPo batteries and provides regulated 5.2V power, digital I2C voltage and current monitoring, multiple ESC power outputs.
-Selectable 8V / 12V auxiliary output for UAV peripherals.

-Integrated Pixhawk and Raspberry Pi companion computer baseboard designed for advanced UAV, autonomous vehicle, robotics, and development applications.
-Supports Raspberry Pi Compute Module 4 and compatible Pixhawk flight controller modules, with direct TELEM2 communication, Ethernet connectivity, dual CAN buses, 16 PWM outputs.
-Multiple GPS and telemetry ports, USB interfaces, Micro HDMI, and CSI camera support.

-433MHz SiK telemetry radio for UAV ground station communication.
-Plug-and-play solution for Pixhawk-compatible flight controllers.
-Provides reliable low-power telemetry for mission setup and monitoring.

-Professional Pixhawk standard baseboard designed for Pixhawk 5X, Pixhawk 6X, and compatible Pixhawk Autopilot Bus flight controller modules.
-Features 16 PWM outputs, dual digital power inputs, three telemetry ports, dual GPS and CAN interfaces, Ethernet, USB, SPI, I2C, RC inputs, and an aluminum CNC enclosure.
-The V2A configuration provides a compact and robust solution for professional UAV integration.

-The Holybro X500 V2 ARF Kit is an Almost-Ready-to-Fly 500 mm carbon fiber quadcopter kit designed for Pixhawk-based UAV development, research platforms, education, and professional drone prototyping.
-It comes with the X500 V2 frame, pre-installed Holybro 2216 KV920 motors, 20A BLHeli_S ESCs, 1045 propellers, and a power distribution board with XT60 / XT30 connectors for fast and clean integration.
-Lightweight, robust, and easy to assemble, the X500 V2 ARF Kit is ideal for developers, students, and drone integrators building a reliable UAV test platform.

-The Holybro X650 ARF Kit is an Almost-Ready-to-Fly 650 mm carbon fiber quadcopter kit designed for Pixhawk-based UAV development, research platforms, education, and professional drone prototyping.
-It comes with the X650 V2 frame, pre-installed T-Motor MN4014 KV330 motors, Tekko32 F4 45A ESCs, NeoPixel WS2812 LEDs, Gemfan 1555 carbon fiber propellers, and a power distribution board with XT60 / XT30 connectorsfor fast and clean integration.
-Robust, foldable, and easy to assemble, the X650 ARF Kit is ideal for developers, students, and drone integrators building a reliable medium-payload UAV test platform.